The catalog
Course Catalog
Self-paced safety training for construction and general industry, with a verifiable certificate for every completion. Most of the catalog is also available in Spanish — switch with the control below.
- Every course includes
- English and Spanish for most courses — same price either way
- Seat time measured on the server, not on the honor system
- A tamper-evident completion record
- A certificate anyone can check at /verify, no account needed
Aerial Lift & MEWP Safety
Intermediate · MIG-CON-202
Safe operation of boom lifts and scissor lifts — the classroom half of operator training (ANSI A92 / OSHA 1926.453 & 1910).
Asbestos Awareness
Introductory · MIG-CON-103
Recognize asbestos-containing materials and avoid exposure (29 CFR 1926.1101 / 1910.1001).
Cranes & Rigging Awareness
Intermediate · MIG-CON-205
Awareness-level training on 29 CFR 1926 Subpart CC and sling/rigging requirements under 1926.251 — roles, power lines, ground conditions, hardware, and keeping clear of the load.
Excavation & Trenching Safety
Intermediate · MIG-CON-203
Soil classification, protective systems, and daily inspections under 29 CFR 1926 Subpart P.
Excavation Competent Person
Advanced · MIG-CON-302
The competent-person body of knowledge for excavation and trenching under 29 CFR 1926 Subpart P.
Fall Protection Awareness
Introductory · MIG-CON-105
Recognize fall hazards and use personal fall arrest systems correctly (29 CFR 1926 Subpart M).
Fall Protection Competent Person
Advanced · MIG-CON-301
The competent-person body of knowledge for fall protection in construction under 29 CFR 1926 Subpart M.
Ladder Safety
Introductory · MIG-CON-101
Choose, set up, and climb portable ladders safely (29 CFR 1926 Subpart X / 1910 Subpart D).
Lead Safety Awareness
Introductory · MIG-CON-106
The construction and general industry lead standards — exposure limits, the presumed-exposure tasks that trigger protection before anyone samples, blood lead monitoring, medical removal, and the hygiene rules that keep lead out of your car and off your kitchen floor.
Respirable Crystalline Silica Awareness
Introductory · MIG-CON-102
Health effects, exposure control plans, and Table 1 methods under 29 CFR 1926.1153.
Scaffold Safety Awareness
Introductory · MIG-CON-104
Safe use of supported scaffolds for users and erectors' awareness (29 CFR 1926 Subpart L).
Steel Erection Safety (Subpart R)
Intermediate · MIG-CON-107
The 15-foot trigger height, connectors and controlled decking zones, the concrete-strength letter that gates the whole job, column anchorage, multiple lift rigging, and why steel erection has its own fall protection rules.
Welding, Cutting & Hot Work Safety
Intermediate · MIG-CON-201
Control fire, fume, arc, and gas hazards of hot work (29 CFR 1910 Subpart Q / 1926 Subpart J).
Work Zone & Flagger Safety
Intermediate · MIG-CON-204
Temporary traffic control, flagging procedures, and struck-by prevention under 29 CFR 1926 Subpart G and MUTCD Part 6.
Arc Flash & Electrical Safety (NFPA 70E)
Advanced · MIG-GI-301
Training for qualified electrical workers on shock and arc-flash hazards under NFPA 70E and OSHA Subpart S.
Arc Flash / NFPA 70E Refresher
Intermediate · MIG-GI-209
The three-year refresher for qualified persons — the electrically safe work condition, the energized work permit, shock and arc flash boundaries, and reading your own equipment labels.
Bloodborne Pathogens
Introductory · MIG-GI-103
Protect yourself from HBV, HCV, and HIV under OSHA's Bloodborne Pathogens standard (29 CFR 1910.1030).
Bloodborne Pathogens Annual Refresher
Introductory · MIG-GI-110
The annual bloodborne pathogens refresher required by 29 CFR 1910.1030(g)(2)(ii), for workers who have already completed full training.
Cold Stress Prevention
Introductory · MIG-GI-108
Work safely in the cold — recognize and prevent hypothermia, frostbite, and cold-weather hazards.
Confined Space Awareness
Intermediate · MIG-GI-205
Recognize permit-required confined spaces, understand entry roles, and stay out of the rescue statistics (29 CFR 1910.146 / 1926 Subpart AA).
Electric Power Generation, Transmission & Distribution (1910.269)
Intermediate · MIG-GI-213
The utility standard — qualified employees and proficiency, job briefings, de-energizing and grounding, the equipotential zone, enclosed spaces, minimum approach distances, and the arc-rated clothing rule that turns on an incident heat energy estimate.
Electrical Safety Awareness
Intermediate · MIG-GI-202
Recognize and avoid electrical hazards for non-electrical workers (29 CFR 1910 Subpart S / 1926 Subpart K).
Emergency Action Plans
Introductory · MIG-GI-211
What 1910.38 actually requires, the six mandatory elements, exit routes and alarms, accountability after evacuation, and the drills the standard does not require but you should run anyway.
Ergonomics: Office & Industrial
Introductory · MIG-GI-210
Musculoskeletal disorders, the risk factors that cause them, and what actually fixes a workstation — for desks, for production floors, and for the hybrid arrangements in between.
Fire Safety & Portable Fire Extinguishers
Introductory · MIG-GI-102
Fire prevention, the fire triangle, extinguisher classes, and safe use under 29 CFR 1910.157 & Subpart L.
Forklift Operator Refresher & Re-Evaluation
Introductory · MIG-GI-113
The three-year refresher for certified operators — stability, capacity, inspection, pedestrians, and the tipover rule (29 CFR 1910.178(l)).
Forklift Operator Theory (Powered Industrial Trucks)
Intermediate · MIG-GI-207
The classroom half of operator training under 29 CFR 1910.178 — stability, capacity, safe travel, and fueling/charging.
Formaldehyde Awareness
Introductory · MIG-GI-217
The four airborne numbers and the two solution percentages, why the smell is not a monitor, the eyewash and drench-shower thresholds, medical removal, and the laboratory carve-out that puts histology squarely under this standard.
Hazard Communication (HazCom / GHS)
Intermediate · MIG-GI-204
Labels, pictograms, and safety data sheets under 29 CFR 1910.1200 — the right-to-know training nearly every workplace requires.
Hearing Conservation
Introductory · MIG-GI-106
Protect your hearing from permanent, painless noise damage under 29 CFR 1910.95.
Hearing Conservation Annual Refresher
Introductory · MIG-GI-101
The annual refresher required by 29 CFR 1910.95(k) — assumes you are already enrolled in your hearing conservation program.
Heat Illness Prevention
Introductory · MIG-GI-105
Recognize, prevent, and respond to heat illness — water, rest, shade, and acclimatization.
Heat Illness Prevention (California)
Introductory · MIG-GI-111
Cal/OSHA 8 CCR §3395 — water, shade, cool-down rests, high-heat procedures, and acclimatization.
Hexavalent Chromium (Chromium VI)
Introductory · MIG-GI-215
The PEL and action level, where Cr(VI) is actually generated, the welding exposure nobody plans for, regulated areas, medical surveillance, and the housekeeping rules that decide whether the dust stays put.
Hydrogen Sulfide (H2S) Awareness
Introductory · MIG-GI-216
The gas that kills rescuers — olfactory paralysis, the ceiling limits and IDLH, why it collects in low places, detection and alarm setpoints, escape versus rescue, and the reason smell is the worst possible warning system.
Laboratory Safety & the Chemical Hygiene Plan
Intermediate · MIG-GI-214
The Laboratory Standard — what makes a workplace a laboratory, the Chemical Hygiene Plan and its annual review, particularly hazardous substances and designated areas, exposure determination, and why the lab standard displaces most of Subpart Z but never the PELs.
Lockout/Tagout (Control of Hazardous Energy)
Intermediate · MIG-GI-206
The energy-control principles behind 29 CFR 1910.147 — for authorized and affected employees.
Lockout/Tagout for Authorized Employees
Advanced · MIG-GI-303
For the people who apply the locks: energy control procedures, the six-step application sequence, group lockout, shift transfer, and the annual periodic inspection (29 CFR 1910.147).
Machine Guarding
Intermediate · MIG-GI-201
Recognize mechanical hazards and the guards that prevent amputations (29 CFR 1910 Subpart O).
Permit-Required Confined Space: Entrant, Attendant & Entry Supervisor
Advanced · MIG-GI-302
Role-specific training for the three people a permit entry depends on — what each one must know, must do, and must never do (29 CFR 1910.146 / 1926 Subpart AA).
Personal Protective Equipment (PPE) Basics
Introductory · MIG-GI-104
Head, eye, hand, foot, and hearing protection — selection, use, and limits (29 CFR 1910 Subpart I / 1926 Subpart E).
Process Safety Management (PSM)
Intermediate · MIG-GI-212
The fourteen elements of 1910.119 — what makes a process covered, process hazard analysis, management of change, mechanical integrity, and why the standard exists because personal safety statistics do not predict catastrophic releases.
Respiratory Protection
Intermediate · MIG-GI-203
Respirator types, fit, use, and care under OSHA's Respiratory Protection standard (29 CFR 1910.134).
Respiratory Protection Annual Refresher
Introductory · MIG-GI-109
The annual refresher required by 29 CFR 1910.134 — for workers already trained and enrolled in an employer respiratory protection program.
Slips, Trips & Falls Prevention
Introductory · MIG-GI-107
Prevent the most common workplace injuries — walking-working surface hazards (29 CFR 1910 Subpart D).
24-Hour HAZWOPER
Certificate · MIG-HAZ-404
Initial training for occasional and low-exposure site workers. In development — not yet available to buy.
Online training alone does not meet 29 CFR 1910.120 — employer hands-on training also required.
40-Hour HAZWOPER
Certificate · MIG-HAZ-405
Initial training for general site workers at hazardous waste operations. In development — not yet available to buy.
Online training alone does not meet 29 CFR 1910.120 — employer hands-on training also required.
8-Hour HAZWOPER Refresher
Certificate · MIG-HAZ-401
The annual refresher required to stay current. In development — not yet available to buy.
Online training alone does not meet 29 CFR 1910.120 — employer hands-on training also required.
8-Hour HAZWOPER Supervisor
Certificate · MIG-HAZ-402
The management add-on required for site supervisors. In development — not yet available to buy.
Online training alone does not meet 29 CFR 1910.120 — employer hands-on training also required.
OSHA 10-Hour Construction (Online)
Certificate · MIG-OSH-410
The 10-hour OSHA Outreach card for construction workers. In development — not yet available to buy.
OSHA 30-Hour Construction (Online)
Certificate · MIG-OSH-430
The 30-hour OSHA Outreach card for supervisors and safety-responsible workers. In development — not yet available to buy.
Incident Investigation & Root Cause Analysis
Intermediate · MIG-SM-202
Running an investigation that finds why the conditions allowed the incident, rather than stopping at who made the mistake — evidence, interviewing, causal analysis, and corrective actions that hold.
OSHA Recordkeeping: Forms 300, 300A & 301
Intermediate · MIG-SM-201
Deciding what is recordable, counting days correctly, certifying and posting the annual summary, and knowing which events must be reported to OSHA within 8 or 24 hours (29 CFR Part 1904).
DOT HAZMAT General Awareness & Security
Intermediate · MIG-TR-201
The general awareness, safety, and security awareness training every hazmat employee must have, and must repeat at least every three years (49 CFR 172.700–172.704).
DOT Supervisor Reasonable Suspicion Training
Intermediate · MIG-TR-202
The full 60 minutes on alcohol misuse and 60 minutes on controlled substances required by 49 CFR 382.603 — the indicators, the determination standard, the documentation that survives review, and the Clearinghouse consequences that followed 2020.
Defensive Driving & Fleet Safety
Introductory · MIG-TR-101
For anyone who drives on company business — the physics of stopping, space management, distraction and fatigue, backing, adverse conditions, and what the law actually requires of employers and drivers.